- Ic 7800 cat port settings how to#
- Ic 7800 cat port settings install#
- Ic 7800 cat port settings serial#
- Ic 7800 cat port settings pro#
- Ic 7800 cat port settings software#
Select Remote IP in the Port list and enter the IP address and port number for the radio in File>Settings>Radio/Ant>Radio A-D>port.Ī variety of WiFi-to-serial and Ethernet-to-serial adapters are available commercially.
![ic-7800 cat port settings ic-7800 cat port settings](https://www.fbnews.jp/201805/technical_en/images/01.jpg)
This can be done using a native Ethernet port on a radio (such as the Ten-Tec Omni-VII) or through an Internet-to-serial adapter.
![ic-7800 cat port settings ic-7800 cat port settings](http://wiki.robotz.com/images/6/6d/Fldigi-ic7600-460x340.jpg)
Sample schematics are provided below.Įach radio selection has a special provision to connect to a radio through an Internet connection. Level converters are available from the rig's manufacturer or other suppliers for this purpose, or you can construct your own for a significant savings. Some radios require the addition of a level converter to adapt to RS-232 signal levels. It may be necessary to reduce the Baud rate if communications are unreliable. When the communications parameters are adjustable, it is generally best to set the Baud rate as high as possible to improve communications and control performance. These parameters can be specified in the File, Settings, Radio/Ant window for those radios that are adjustable. Many radios have fixed communication parameters, in which case CommCat sets the necessary Baud rate, data bits, parity and stop bits.
Ic 7800 cat port settings serial#
In both cases, drivers are required to cause the USB connection to appear the same as a classic serial port.Īny serial port from 1 through 255 can be used. (CommCat supports the Collins KWM-380 through a parallel port.) Some radios now feature USB ports for connection to your computer, or you can use a USB-to-serial adapter if necessary. Radios are controlled by CommCat through serial ports. Use HRD to control your radio and CommCat to help chase DX, feeding frequency and mode data to HRD Pegasus, Jupiter (both with support provided through and external program such as N4PY), Orion, Orion II, Omni VI+, Omni VII
Ic 7800 cat port settings software#
when the software transmits, the control program takes over and it all works! Then in your software, select the RTS method for PTT and the application (virtual) com port you have created (com9 for me).Īnd run your software and it will work, This demo is my own WSPR-X setup for windows. Then run the cat7200 software, select the control port form the icom (com4 for me), and the virtual serial port as the application port (com9 for me)
Ic 7800 cat port settings how to#
the websites show how to set up the radio also, with menu settings etc, make sure its using the Digital mode.
Ic 7800 cat port settings pro#
Some have reported issues with unsigned drivers and windows 8, the websites have tips on how to solve those, i didnt have any issues on my setup, the below is my apple mac using a virtual machine inside parallels and windows 7 pro 32bit.
Ic 7800 cat port settings install#
The Program works in conjunction with the "User Mode Virtual Serial Port Driver" from the BPQ32įollow the instructions on both Barry and John’s website’s and install the virtual serial Port. Originally written for the ICOM 7200, but has also been tested with an ICOM 7100/7410/9100. Support PTT via CAT commands to be used with ICOM radios with built in sound cards. It allows sound card based digital modem programs, such as the UZ7HO soundmodem, which do not John’s website says CAT7200 converts changes in the RTS signal on a Virtual COM Port to ICOM CI-V PTT commands. Recently I stumbled upon this website from Barry K7BWH that pointed to a bit of software from a UK Ham John, G8BPQ that creates a virtual com port and converts the RTS method to C-IV Cat Commands and makes the radio TX! The software is called CAT7200, and was initially designed for the IC7200 radio, it works on any of the recent Icoms with built in USB port, the IC9100, IC7410, IC7200, 7600 and IC7100 etc. I had given up on the radio usb method and purchased a SignaLink which did the job. a number of the software programs I like to use (WSPR) don’t have CAT radio TX control, they use the RTS method.
![ic-7800 cat port settings ic-7800 cat port settings](https://www.fbnews.jp/201805/technical_en/images/10.jpg)
It works as advertised, and works generally well. The IC-9100 that I have has a USB port on the back that allows audio and cat control directly from the radio.